A platelet-rich fibrin (PRF) membrane is made from the patient's own blood. The blood is drawn into tubes that promote coagulation and immediately centrifuged to form a fibrin clot. The clot is removed and gently pressed into a membrane. Its quality depends especially on the time between the blood draw and centrifugation, the type of tube, the temperature, and the way the clot is pressed.1
What do you need for PRF membranes?
This article is based on the guidance on leukocyte- and platelet-rich fibrin (L-PRF) published by Quirynen et al. in 2024 in Periodontology 2000. It is based on literature reviews from the same issue and was reviewed by a panel of clinicians. The guidance is the authors' own and has not been adopted by a professional association, and the authors themselves state that the preparation advice is largely based on laboratory studies.1 If you first want to know what PRF is and how it works, read What is PRF?
According to the guidance, you need tubes that promote coagulation, e.g. glass tubes, a butterfly needle for drawing blood, a centrifuge that stands stably without vibrating, and a compression box for pressing the clots.1
-
Complete PRF setup
Centrifuge, PRF box with instruments, tubes for membranes and liquid PRF, butterflies and stasis in one package.
View product → -
Horizontal centrifuge BP 200
Swing-out centrifuge for PRF with digitally controlled speed and time.
View product → -
Glass tubes for PRF membranes
10 ml vacuum glass tubes without additives, so the blood coagulates naturally.
View product → -
PRF box with instruments
Box for pressing the fibrin clots into membranes, with 6 instruments.
View product → -
21G butterfly with holder
Safety butterfly for drawing blood directly into the PRF tubes.
View product →
How are PRF membranes made?
The procedure has five phases. The exact protocol for force, time, and number of tubes depends on the centrifuge, the tubes, and the indication, and is best learned through practical training (see Education).
1. Blood draw
The blood is drawn by venipuncture directly into the tubes. Because no anticoagulants are added, coagulation begins immediately. The workflow must therefore be planned so that the tubes quickly get into the centrifuge.1 If you also need to use liquid PRF, it is drawn into uncoated plastic tubes, see i-PRF: what is liquid PRF?
2. Centrifugation
During centrifugation, the blood separates into layers, and a fibrin clot forms over the red blood cells. The force the blood is exposed to depends on the radius of the centrifuge, so the same rotational speed does not give the same result on two different centrifuges.1
The original L-PRF method was developed on fixed-angle centrifuges, and that is the one described in the Quirynen guidance.1 Since horizontal centrifugation has come along, where the tubes swing out and lie horizontally. Farshidfar et al. reviewed in 2025 in Periodontology 2000 studies of PRF produced on a horizontal centrifuge. 13 studies directly compared the two methods: 11 assessed horizontal centrifugation as best, especially due to more leukocytes and a more even distribution of the cells in the clot, and 2 found no difference. 12 of the 13 studies were laboratory or animal studies, and the authors call for randomized clinical trials.2 The BP 200 is a horizontal centrifuge.
3. The clot is removed
The clots are removed from the tubes, and the red blood cells are carefully removed. The end that lay against the red blood cells should not be cut away. According to Quirynen et al., most of the platelets and leukocytes are located just below them, and that is the biologically most active part of the clot.1 In horizontally centrifuged PRF, the platelets distribute themselves more evenly, but the leukocytes still gather at the boundary with the red blood cells.2
4. The clots are pressed into membranes
The clots are gently pressed in the compression box, so the liquid is pressed out, and a membrane is formed. With a compression set, they can instead be pressed into round plugs that fit in an extraction socket. The liquid that is pressed out is called exudate, and Quirynen et al. use it to rinse the socket or defect before the PRF is placed in.1
5. Storage and placement
The membranes remain viable for at least 3 hours, as long as they lie covered and do not dry out. When a membrane is placed, the active end must face the area that needs to be healed or built up.1 Quirynen et al. emphasize that the number of membranes matters for the result, and that the effect in most applications was worse with uncompressed clots than with membranes.1
What do the studies show in extraction sockets? Al-Maawi et al. reviewed in 2021 in International Journal of Implant Dentistry 20 randomized or controlled studies of PRF in fresh extraction sockets. Of the 6 studies that measured pain, 4 found significantly less pain with PRF than with spontaneous healing. Three of four studies with clinical measurements found less bone loss with PRF after 8-15 weeks, while the only study that measured after 6 months found no difference. The studies were too different for a meta-analysis, and most had a relatively high risk of bias.3 Read more about the procedure in What is socket preservation?
What mistakes give a poor PRF membrane?
The typical pitfalls. According to Quirynen et al., the quality of an L-PRF membrane depends on the time from drawing to centrifugation, the tubes, the centrifugation, the temperature, and the way the clot is pressed.1
- Waiting time before centrifugation. When the blood begins to coagulate in the tube, the clot becomes crumbly.1
- Too cold. If it is too cold during centrifugation, a well-structured clot is not formed.1
- Vibrations. Vibrations in the centrifuge affect the structure and cell content of the clot.1
- Wrong tubes. The strength of the clot depends on the inside of the tube.1
- The active end cut off. The end against the red blood cells contains the most platelets and leukocytes.1
- Anticoagulant treatment overlooked. If the patient takes anticoagulants, the centrifugation must be extended.1
- Drying out. The membranes must lie covered until they are used.1
Where do you learn to make PRF membranes?
The procedure is the same everywhere, but force, time, number of tubes, and number of membranes depend on the centrifuge and the indication. Puredent holds blood draw courses for clinical staff and courses in PRF, e.g. the full-day course with Professor Marc Quirynen from KU Leuven, and offers an online course with Richard Miron. The textbook Understanding Platelet-Rich Fibrin goes through centrifugation and protocols chapter by chapter.
See upcoming courses in PRF and blood drawFrequently asked questions about PRF membranes
How do you make a PRF membrane?
The blood is drawn into tubes that promote coagulation and immediately centrifuged to form a fibrin clot. The clot is removed, the red blood cells are removed, and the clot is gently pressed in a PRF box into a membrane.1 The exact protocol depends on the centrifuge and the tubes.
How long can a PRF membrane last?
According to Quirynen et al., the membranes remain viable for at least 3 hours, as long as they lie covered in the compression box and do not dry out.1
What tubes should you use for PRF membranes?
Tubes that promote coagulation, e.g. glass tubes. The strength of the clot depends on the inside of the tube.1
Why does the PRF clot become crumbly?
Typically because the blood has begun to coagulate before it got into the centrifuge, or because it was too cold during centrifugation. Then an uneven fibrin mass with unknown content is formed.1
Is a horizontal centrifuge better for PRF membranes?
In a review in Periodontology 2000, 13 studies compared horizontal centrifugation with fixed-angle. 11 found an advantage in horizontal centrifugation, especially more leukocytes and a more even distribution of the cells, and 2 found no difference. 12 of the 13 were laboratory or animal studies, and the authors call for clinical trials.2
Interests. Puredent distributes equipment for PRF and sells courses and textbooks with Richard Miron as well as courses with Marc Quirynen. Quirynen is the first author of the guidance. The authors behind it state that they have no commercial interests in blood concentrates, but state that they may have received research support from companies in the industry.1 Miron is a co-author of the Farshidfar review and according to the source's own statement founded Miron Research and Development in Dentistry, which has intellectual property rights to the production of PRF.2 Al-Maawi et al. declare no conflicts of interest.3
Sources
- Quirynen M, Blanco J, Wang HL, Donos N, Temmerman A, Castro A, Pinto N. Instructions for the use of L-PRF in different clinical indications. Periodontol 2000. 2024;97(1):420-432. DOI · freely available
- Farshidfar N, Apaza Alccayhuaman KA, Estrin NE, Ahmad P, Sculean A, Zhang Y, Miron RJ. Advantages of horizontal centrifugation of platelet-rich fibrin in regenerative medicine and dentistry. Periodontol 2000. 2025;99(1):216-267. DOI · freely available
- Al-Maawi S, Becker K, Schwarz F, Sader R, Ghanaati S. Efficacy of platelet-rich fibrin in promoting the healing of extraction sockets: a systematic review. Int J Implant Dent. 2021;7(1):117. DOI · freely available



Share:
What is GBR? Guided Bone Regeneration and barrier membranes
What is extended PRF?